Category Archives: Front Wind Splitter

Dartlene Front Wind Splitter

 CoiloversUntitled
Version R front Joe

Basic Splitter: $289.00 (gloss black finish, with support rods, includes all mounting hardware) you choose: Version S (top), Version R (rounded version above) and Version B (looks like a “B” below.)  Chicagoland installation is possible, although you can likely do it yourself in an hour or less!  (You do not need to remove the front bumper.)  Shipping is $70.00 to most of the US.

If you are interested in the lip underneath the splitter, or the side wings, they can be specially ordered – just let us know when you fill out the form.

The car pictured (above) has a carbon fiber lip underneath the splitter, as well as side wings – these items are sold separately. (Version S pictured above, Version B is below:)
stephen 12

version B 1

Parts are now available!  We make them to order, so it will take a few weeks to get your custom splitter to you, depending on add-ons.  The alumalite and basic hardware is local, but some of the rods and wings will take extra time to order and build.  Keep in mind, this product is not available ANYWHERE ELSE!

We offer local installation as well – We will need to see your car for an actual quote.  We can change the position of the support holes, too.  This will work with the Mopar lip as well (although not recommended) and the Deyeme Racing underbody panel, although you will need eight 2.5″ M5 bolts in addition to the supplied hardware.

We can also offer a rounded design, Version R: (The car pictured has a carbon fiber lip underneath the Version R splitter, this is sold separately.)

Dartlene Wind Splitter - Round Version

We now offer a brand new design, version G, here shown on this Charger, and below on the red Dart:

Charger Splitter 2015+

The wind splitter is made out of 6 mm (1/4”) alumalite, which is the lightest, strongest weatherproof material I could find.  This is corrugated for strength and weight, and is completely waterproof.  Keep in mind, if you crash into something, such as parking block or curb – it may break.  I cannot promise any functional high speed gains, as I just don’t have the equipment to do such testing – they do look pretty badass, though!

Below is the Version S splitter shown in carbon fiber wrap, and no lip / guard:

Version S Red Dart 3
I am extremely proud to announce the version 2.0 splitter is now 100% functional, and bolts to the frame underneath. It isn’t quite a full underbody shield, but it does support the two front pieces, and protects the underside, as well. The unit is very solid & rigid, and the support rods are not necessary, unless you want to be cool 🙂 Wot Box, Black Alumalite Splitter, Wiring Dartlene Alumalite Front Splitter Dart '13-16

There are several options available, and unfinished will be black alumalite, and could be wrapped, painted, dipped, etc by you! The version shown below has the basic rods, wings, simulated carbon fiber underlip / splitter protector, and is carbon fiber wrapped.  Keep in mind, the bottom side will be unfinished, and if you crawl on the ground, you will see the seams of the wrap, and partial bare alumalite.  The basic rods have aluminum shafts, but the nuts and mounts are steel, and may rust in extreme weather conditions.

This includes all of the mounting hardware and holes, some of which I could only find in silver or clear, so these would be hand painted.  Instructions included, but will require some minimal mounting skills. If you have the stock lower grille, than I will include several 1” washers (also painted black) to mount to the OEM lower grille.  The rods are completely optional, as the splitter is quite strong without them, and the rods are really only aesthetic, anyway.

All of these upgrades are fairly simple, but do take a bit of time and materials to complete.  If you are moderately good at mechanical things, you could easily do the upgrades, yourself.  I can still provide mounting holes, if you request it, as the support rods and side wings are certainly optional.  If you want to paint or dip it yourself, be sure to use adhesive promotor, and then a primer, before applying the paint, or dip.

– We accept Visa/MasterCard/Paypal –  Use the contact form below, and be sure to specify which options you would like, and we will send you a Paypal invoice for the total.

*Installation Instructions can be found here.
Dartlene Wind Splitter - Round Version

UntitledUntitledWot Box, Black Alumalite Splitter, Wiring Wot Box, Black Alumalite Splitter, Wiringfront splitter front dart

20160424_190543  collin close

As you can see, our splitters hold up better than your Dart!  Here are the results of a minor crash on a Dart with version “S” installed:Crashproof

With a little creativity (and $40/hour labor charge) we can customize your splitter to match your individual, unique needs!  Yoder’s splitter has some custom alumalite wings, carbon fiber short trim, and angled spacer covers:UntitledIMG_5227

Tags:

How to Build and Install a Custom Front Wind Splitter / Front Lip / Diffuser / Chin Spoiler

Custom DIY Front Splitter / Chin Spoiler / Front Lip / Ground Effects
IMG_20160428_003030The Mopar lip kit is fine for most people, in fact, it looks quite nice. The problem I had is the cost, and the fact that everyone has that one option. I have done a ton of research on splitters, lips, spoilers, etc., but I am in no way a car, or racing expert. Use my instructions as a guide – then put your own flavor on it. Not everyone will like this style, but you can see what I struggled with, and why I made the decisions I did. I hope you like it, but if you don’t, you can build yours any way you want.Before you ask, a front splitter is designed to produce extra downforce at high speeds to the front wheels for better handling and traction. These are often used in conjunction with rear spoilers in race cars, and won’t have much of an impact on driving below 80 MPH. They usually fill the bottom portion of the car from just ahead of the front wheels to a few inches beyond the front of the car. Oh, and they also look freakin’ baddass!Typically, a front splitter should fill in the entire space in front of the wheels, and should not have any spaces or openings. My Dart has the Aero package, which means it is already covered under the entire bottom. It also means the aero panels protrude down past the fascia. If you put a flat piece of material under the whole thing, it can’t touch the sides b/c the oil drain area sticks down too far. A splitter should also be flat if possible, so I omitted the center area in the splitter, and left it as is. This also reduced the weight of my entire splitter to less than 3 lbs.Now the question everyone asks (go ahead): What’s it made out of? Alumalite. “Alumalite is a strong, aluminum composite panel made of with a high density corrugated polyallomer (CPA) core that will not swell, corrode, rot, wick water, or delaminate even under prolonged water exposure. Factory-baked polyester painted aluminum faces add high gloss brilliance and rigidity.”There are many ways to do this, and the cheapest would be plywood, and then covered in polyurethane resin to make it waterproof. The problem with this is weight. ABS plastic is also pretty expensive, and also heavy. I looked up what the professional racers use, and most of them are using some form of alumalite. It is incredibly strong and lightweight. It can also be bent, if needed, and is completely waterproof. The best way to describe it is two, thin aluminum sheets, separated by a corrugated material.
20160310_143825So then I researched, “Who else would use Alumalite,” and I found they use it to make signs! I reached out to some local sign companies and confirmed this. All you have to do is ask them for scraps. I needed something that was at least 72” x 26” – I ended up finding a piece for the price of a 12-Pack of Anti-Hero IPA (although he is my buddy, and did the graphics for Dartlene Orangina)
20160308_201807
20160310_194925
20160310_194934The first thing I needed was a template, and a way to line things up. The easiest way to do this was to start with the Mopar Front lip. When tracing the lip, you have to be careful, and take into account the 7/8″ rise in the middle of the fascia. If you press the lip flat and trace it, along with the holes, once you hold your trace up to the car, you will find the outer edges and holes are too wide. Be careful to trace the piece while keeping it’s shape, holding the edges up.
20160315_011531
20160313_171527I followed the front angles of the car, but I wanted a little more aggressive appearance. I also knew that I wanted to wrap the thing in carbon fiber, and if you’ve done any wrapping, you’ll know how difficult it is to wrap around a curved edge. If you want to try this method, you’d have to cut along the top edge, and use a separate piece for the front / bottom. I used cardboard to create my original template, so I could mess with it, as well as hold it up to the car for rough placement. I was concerned the cardboard would bend, but the final material would not, so I also had to keep in mind the upward arch in the middle if it is attached flush to the fascia.
20160417_134220
20160417_134231
20160417_134353Now that I had my template, I dry fitted it to the car to make sure. Then I traced it onto the alumalite, and cut the front shape and the inner circle, leaving a bit extra on the inside, which could be trimmed. As it was, I had to adjust the holes a little bit after the final cut, as I was using the same holes to secure the aero panel and the Mopar front lip, if you had one. The 4 screws in the rear connected perfectly to the cut splitter, but it had to bend up too much in the middle to work, so I needed spacers. I took some brass tubing I had lying around, and cut it into (4) 7/8” pieces. Then I sanded and painted them black. Washers were used above and below the splitter and spacers, and I found some wood screws that matched the thread of those metal clips in the aero panels. Lock washers were put on the very bottom to secure it.This is without the spacers:
20160417_144829
20160417_144836
20160417_144841
20160417_144948
20160417_144958
20160417_170311

Spacers:
20160424_190539
20160424_190543

Underneath the spacers:
20160424_190552
20160424_190556

Then I wrapped the splitter, easily terminating the ends of the wrap on the bottom, as no one can see that, unless the car is on a lift. For extra credit, I guess you could wrap or paint the bottom, too.
20160423_005240
20160423_005248

Rough mockup:
FB_IMG_1461423321194

After I had the flat shape, I added my side fins, using simple nut and bolt connections on either side. I lined up the outside to the shape of the car, and the back to the wheel well. I originally was going to bend the alumalite into the fins, but I wanted something that looked a little better and wasn’t as thick. The edge of alumalite looks a like cardboard, so it needs to be covered, wrapped, or filled in. I found some thin aluminum and could easily cut and bend it as needed. Then I simply drilled a couple of holes in the new “L” shaped wings, and bolted from underneath. Shazam!
20160423_102432
20160423_102438

I mounted the splitter using the 8 holes in the bottom fascia that connects the aero panel. The rear 4 were factory screws, into the factory holes, and the front 8 were factory holes, with longer, wood screws that matched the thread size. I later painted the silver bolts black, as well.

Finally, the last step was the rods. I already had replaced the grilles with mesh that had medium sized holes. I painted a couple washers black, and used them in front and behind the grille to secure it, and then bolted it to the splitter. I was able to do all of this without removing the fascia, but it was a bit tricky squeezing in and securing the nut on the backside. They are adjustable, so you can make them ultra-secure. I’m not saying you should stand on this thing, but it is very secure, and has lasted, so far!
20160425_075743
20160425_075757
20160424_203318
20160424_222720
20160425_075821

I later added a lip underneath the splitter, to give it a more “lowered” look – I think it makes it more aggressive, but certainly works without it:
FB_IMG_1464560314497
20160621_203048

Tags:

Front Wind Splitter

New Yoderian Front Wind Splitter / Chin Soiler / Front Lip √ No protective lip, yet, in these pics:

This includes support rods, wings, and carbon fiber wrap.

20160425_075743
20160425_075757
20160425_075821
20160425_075828
20160425_075845
20160425_075904
20160425_075932

I later adjusted the splitter, dropping the nose a little bit, making it perfectly flat:
instagram

Tags: