Dartlene Wins her first Car Show!

Dartlene and I won our first car show in St. Charles, IL!! “Best Looking / Best Lights”

Latest mod attempt is white LED DRLs. I bought a set from Derek, and I’ve got them working on the turn signal circuit with resistor, but mine doesn’t like the resistor on the DRL, for some reason. I’ve been experimenting all weekend, and there is no reason it’s doing such weirdness. When I put the 50w 6 ohm resistor inline with the turn signals, it stops the fast blink, and no errors. When I put the resistor on the other (DRL) line, it shuts off the DRL and side turn signal lights – too much load, I’m guessing. Strange, as the only other thing I have running is switchbacks connected to the turn signal power, which is fine.

Last ditch effort, I put an led strip under the hood, attached to the DRL to increase the load. I drove 10+ miles through the city, with only one error, and that was 30 seconds after starting the drive, at a light.

Prior, it only happened when my lights were on, and randomly at that. On the way to the car show, and back home, I had a ton of errors. I’m going to keep testing, and I may add another led strip to the other side, for added load. I still get the error on startup, only.

Tags:
Category:

New Headlights (black) and LED switchback Foglight Strips

Next up was to knock out a few things, since I have to take apart the entire front end – with the Aero panels, it was a bit of a pain, especially with the car lowered. I replaced the silver headlights with Black Eagle Eyes (from Amazon or Ebay,) and wired LED fog lights that switch to turn signals (yellow) when activated. They run as the car is running via the fuse block, and switch to yellow turn signals as used. I also replaced the license plate holders.

*Note – The Eagle Eyes Headlights change the bulb socket from the standard 9012, to H8/H9/H11.  All three are the same, unless dealing with halogen bulbs – they are different wattages.

20150522_080316
20150815_231927

original silver light:20150405_201553
20150402_134325 20150403_082302

 

It was a bit of a pain, as you have to remove the entire fascia, including the front Aero paneling underneath. The whole assembly then lifts off of the car. You can find this info on youtube – search Dodge Dart Headlight replacement – you’ll fine a few.

The lights I used are from SiriusLed, but the link is no longer valid – May the force be with you! You can also find many of them on ebay.

There are three wires: one for the +12v white, one for +12v yellow, and a ground. Connect the white +12v line directly to the battery (fused) or find a switchable fuse and use one of those “add a fuse” parts from Amazon. The yellow power and ground were connected to the turn signal circuit. When power is sent to the turn signals, it switches to yellow, and flashes in sync with the turn signal. Be sure to leave enough slack in the cable after the splice so you will be able to change bulbs later, when they burn out.

I used a super strong epoxy to connect the LED to the strip next to the fog light. Mine didn’t have the factory fogs, so it was not hard. You need to drill a small 3/8″ hole on the inside of the strip so the light can peek through from the inside, where the wires are. I chose to leave the factory silver bezel/trim in place, and used the top side of it as a glueing surface

The adhesive bonds in 5 minutes, so you have to stand there like a jackass and hold it tightly in place, as it will want to slide off, or rise up off the trim. The LED can be trimmed as needed, and doesn’t affect the light, so I rounded/tapered one end so it sat flush with the trim. The other (wire) end can go back through the hole and be hidden, so it has a clean look to it.

Be sure to leave enough slack, so if the fascia has to be removed again, you won’t rip the wire connecting it to the headlights. It comes with a removable connector, so it can easily be detached. I’m guessing removing the whole thing will be a bit of a pain, but the led should last a few years, and it has been completely waterproof so far.

The problem is, it makes my headlights look yellow and sickly! I’ve got HID’s going in the headlights later this week.

You can add a switch if you like, but I didn’t. Mine run as soon as the car is running, so I never have to remember to turn them on. Keep in mind, that if you have the DRL on, then it turns on the yellow parking lights up front. When these are activated, it will then turn the fog lights yellow as well. So you can run dual amber upfront for DRL, or you can switch the DRL off and only run the fogs during the day. This is a preference found in the touchscreen.

You can tap into the turn signal wires directly out of the lights. If you peel away some tape, you can cut the wires, and then re-splice them back together with solder and/or electrical tape. I would use that ground as well, as the shortest path to ground is always best practice.
20150523_213356

Tags: