Shifter Linkage Cable Replaced

This was a fun installation!! Burned the crap out of my hand on the downpipe – the front part of my shifter linkage cable broke off. Part # is 68166675AA.

I was trying to race another tuned and bolted Dart – jammed it into third a bit too hard on the third honk, popped the linkage right off! Put it back, but it kept falling off, so I ordered another one. Can’t wait for this scar.

Tags:
Category:

CDV Delete and Review (RRM / Road Race Motorsports)

Review of the CDV Delete from Deyeme Racing

First of all, let me preface this with saying I am no car expert, but I have learned a lot the past 18 months with my Dart. The only thing I can offer is my personal experience, and I hope it helps somebody else out there. My inbox, as well on FB, has been blowing up with people asking about this, so here we go:

I did this installation during the afternoon, after installing the flex rear engine mount, which came in the same box from @DeyemeRacing . I guess I’m their poster-boy this week – lol. I had some prior issues, which is relevant to the topic, so I’ll explain. I bought the Dart last Feb 14 – and the night I brought it home, my clutch sunk to the floor and stayed there. Looking back on the situation, it actually stuck a tiny bit a few times, but I didn’t know enough to recognize it, as it was very subtle. The following week, the Kia dealership, where I purchased the vehicle, replaced the Master and Slave cylinder, as well as the clutch. They tried to blame my driving on the clutch going out – yeah – on the first day I owned it. Anyway, you don’t mess with a Amish guys’s kid – needless to say, a year later Chrysler reimbursed me for everything. Woot Woot!

As time went on, after the replacement, I had 2-3 issues over the next 8 months, where the clutch would stick momentarily, and then pop up. Couldn’t get any video, but I took it back in one time, complaining of the same issue, they couldn’t replace it and claimed to bleed the clutch. It did feel better, and I know they bled it b/c the green outlet nipple was missing (no cap.) As time went on, I would try to analyze the clutch, and I realize that many, if not all, of the “jerky” launches I had in first gear was due to the CDV sticking, ever so slightly, then releasing a moment later, causing a less than perfect launch. I have been driving stick for over 25 years, so I’m pretty confident in my ability to drive any stick, even bigger trucks. If I needed to move quickly, such as WOT, the clutch would stick momentarily. I also noticed (as others did) that on my WOT launches, I would grind third gear. It happened about 5-6 times since I’ve had the car, no more, but it was odd to me.

I also agree with others about the 1-2 shift point. Let me tell you what – this freakin sh!t fixed everything!!  Buy it and get out of here! Go!

What are you still doing here? Ok fine:

Does this feel like a new clutch?
No.

Does this feel stiffer?
Yes, but that may have been accomplished by simply topping off the fluid levels. The clutch feels tight and consistent.

Did I have to re-learn the clutch?
No.

How long did the install take?
2 hours.

Did it change the way I drive?
No.

Does it make me happy?
OMG – Every single launch was perfect, even in slow, city traffic. I have not opened it up yet, I’ve only driven 10 or so miles in city traffic, but A LOT of clutch holding, launches, downshifting, etc. Shifting into second gear was perfect every time. I had no jerkiness, no sticking, no issues, and I couldn’t be happier. I don’t double clutch much in this car, but I do rev match to downshift, and there were no issues there, either – smooth as butter!

This fixes the inconsistencies of the CDV. I really think many Darts’ CDV’s stick a little bit, but so slight that you don’t always notice, until it’s gone. I didn’t have to adjust anything, and driving it was as easy as driving any manual. Also, keep in mind, I never really had issues launching, but looking back, I can see where it was less than consistent. I would say, that if you haven’t done a bunch of mods, this is NOT the easiest installation. The biggest difficulty was bleeding the system.

Two issues I had while doing this installation was removing the CDV without pulling the pushpin completely out. I dropped the pushpin, and it’s very difficult to see in there, so be careful of losing it. The other issue was my air compressor wasn’t powerful enough to use the brake bleeder tool. That fluid drained SOOOO slow. I ended up using a friend to help, so one could pump the clutch and the other monitored the fluid. The biggest thing, is DO NOT LET AIR INTO THE SYSTEM. Make sure fluid stays in your supply tank. I’m not sure if I read it wrong, but I bought 3 quarts of brake fluid, but only needed less than one. It was taking so long to bleed, I ended up topping it off and replacing only what I needed. I’m going to see how it does, as I haven’t opened the other two bottles, but by looking at the tank, I don’t think you could even fit more than a quart in there, but I could be wrong.

I will give more results on the power / racing side on my personal build thread here. I will surely beat my 7.16 second 0-60 now that my clutch responds properly.

If you are in Chicago, New Star Transmission will install it for you for $140 + parts, if you don’t feel confident in your abilities. PM me for details, or google them – ask for David.

OEM CDV:20160530_233527

Tags:
Categories:

Shift Boot, Short Throw Shifter & Interior LEDs

  1. I finally got my parts in the mail all the way from Europe – My Custom Redlinegoods shift boot! I installed this at the same time I installed the MPX short throw shifter, as well as a Momo shift knob. I really thought I wanted the Alfa Romeo Giulietta Carbon Gear Knob – but it was out of stock. I’m patient, so I would have waited, however, after doing more research, i found that this was not the best option. It is a plain grey ball, and didn’t seem to have the leather/comfort/grip/feel that I really wanted.

    This is really the coolest combination! The Redline Leather Shift boot looks AMAZING! They put a lot of detail into the products, and it looked even better in person than it did when I designed it on their website using their color tools. You can pick out stitching color, stripes, two stripes, you can do virtually anything. I got an email right away explaining the international shipping information, and what to expect. It showed up just as they said it would, and I am extremely happy with the whole setup.

    The throw of the shifter took a week to get used to, but now it’s like butter. I have not missed any second gear shifts, and the metal grommets (which replace 4 stock rubber bushings) feel more solid, more like a sports car should. The grip of the MOFO shift knob is groovy as well. Yeah, I know it’s Momo, but now I’m the Mofo!!

    I’ll be showing this beast off tonight at our local Berwyn Cruise Nights at the Depot District! Shazam!
    Name: shifter.jpg Views: 397 Size: 2.79 MB

    yodamusic's Avatar

    I replaced all of the interior lights, as well as the trunk lights with LEDs.
    Name: interior leds.jpg Views: 376 Size: 2.15 MB
    Name: trunk leds.jpg Views: 384 Size: 1.78 MB

    FB_IMG_1466845334706 20160520_180145

Tags: